Portable Power Station IVT PS-1200, 1200 W

Secured current draw via 230 V safety socket

Connected to the 230 V AC output of the digital sine wave inverter, a pure sine wave alternating voltage can be taken safely. Thanks to galvanic isolation of the input and output stage, no additional fuse protection is necessary when connecting a consumer, even in the commercial sector. The peak output power, which is twice as high (2 s), ensures that even loads with high starting currents can be connected safely and without interference.

Please note:
If a multiple socket outlet is connected and several 230 V consumers are used at the same time, the professional associations stipulate that each additional consumer must be protected with a separate RCD or DI circuit breaker. Please obtain information from your professional association or on the Internet at: www.dguv.de

---

Secured current draw via 12 V DC socket

The 12 V DC output is controlled via the MPPTplus⁺ solar controller. This enables reliable power consumption – even when you are not personally on site, e.g. for operating alarm, lighting or cooling systems in warehouses, allotment gardens, holiday homes or boats, as well as in agriculture for pasture fencing or pumps and much more.

---

 

Secured current draw via the two 5 V USB ports (type A)

In addition, two smartphones, tablets, notebooks, battery packs, LED lights and many other small devices can be reliably charged at the two 5 V USB outputs.

The switchable load outputs can be used simultaneously. Charging is possible while the current is being drawn.

The operating time of the Power Station PS-1200 can vary greatly depending on which loads are connected. If you operate consumers with lower power, the operating time is extended. If you use several outputs at the same time, it is shortened accordingly.

Average operating time for electronic devices with the Power Station PS-1200

 

230 V consumer	Operating time
50 W (e.g. laptop charger)	23.0 h
140 W (e.g. e-bike charger)	9.1 h*)
600 W (e.g. drill)	2.0 h
12 V consumer	Operating time
50 W (e.g. TV set)	24.0 h
120 W (e.g. compressor)	10.0 h
*) Corresponds to 3 – 4 recharges of a 36 V / 11 Ah e-bike battery

The valuable inside of the power station is protected by an extremely robust metal housing. The corners are additionally reinforced with edge protection. The sturdy carrying handles make it easy to transport to the place of use.

• Twice the usable capacity
• a weight saving of approx. 65% and last but not least
• an extremely long service life (4000 cycles at 80 % depth of discharge) compared to lead batteries (up to 550 cycles at 50 % depth of discharge).

Individual equipment for your application

The Power Stations can be adapted to your needs on request. On request, individual components of the existing Power Station can be exchanged, omitted or additional ones installed, e.g.
 

• Inverter (capacity and type)
• Battery (capacity and type)
• Charger (amperage)
• Size of the box
• Cable lengths
• and much more.

We will be happy to advise you.

Electronic devices	LiFePO4 battery

IVT products are manufactured to the highest quality and according to strict quality guidelines. Therefore, we are so convinced of the longevity of our products that we extend the legally required manufacturer's warranty free of charge: 3 years on electronic devices, 8 years on LiFePO₄ batteries.

• Power Station PS-1200 (fully equipped)
• Battery charger SH-3.150, 12 V, 10 A incl. mains cable and adapter, 3.3 m
• Connection cable for solar module, 4 m, H07RN-F 2 x 2.5 mm² (max. 50 V/20 A)
• Connection cable for charging booster for 12 V car socket, 2.5 m, 2 x 1.5 mm²

Digital sine wave inverter IVT DSW-1200, 12 V, 1200 W
Item no. 430105
To the product >

---

Absolutely self-sufficient thanks to real sine wave AC voltage

The high-quality digital sine wave inverter DSW-1200 reliably and precisely converts an input voltage of 12 V DC into a real sine wave AC voltage of 230 V/50 Hz. Independent of the public power grid, even sensitive consumers as well as devices with high starting currents can be supplied with power safely and without interference.

The most important features and characteristics

• Output voltage: Real sine wave alternating voltage 230 V/50 Hz
• Continuous output power 1200 W
• High peak output power 2400 W
• Galvanic isolation of input and output stage
• Power start function for loads with high starting current
• Switchable power saving functions (sleep, standby)
• Dynamic deep discharge protection
• Extensive protection functions

LiFePO₄ Premium Batterie FORSTER 12,8 V/100 Ah 200 A-BMS-2.0 | F12-100XB1
Item no. 920040
To the product >

---

Extremely resistant, robust and lightweight
 

The installed LiFePO₄ battery is extremely robust, economical and, thanks to its optimized design, lighter and smaller than conventional lead batteries.

Further advantages of the premium battery series

• High cycle stability
• Short charging times
• Incl.200 A high-load power BMS
• Incl.500 mA Smart measuring shunt and app operation
• Low self-discharge
• High heat tolerance
• Built-in complete "Safety First" protection

Item no. 920033
To the product >

---

Optimum charge

The integrated charge booster serves to optimally charge the installed battery. The charging booster is supplied preset (battery type and charging current). The set 10 A mode prevents the socket in the vehicle from being overloaded. Once the end-of-charge voltage has been reached, the charge booster switches to trickle charging.
 

Item no. 200036
To the product >

---

Highly developed solar charge controllers of the latest generation

Thanks to the MPPT function (Maximum Power Point Tracker), the most effective use of solar power from the solar modules is always guaranteed. The high efficiency (max. 97 %) and the significantly shorter battery charging times enable the best possible power utilization of your solar system.

The most important characteristics and features

• MPPT charging process: highly efficient, fast, battery-friendly
• Multi-stage charging technology
• Microprocessor-controlled charging
• Automatic temperature compensation
• High efficiency max. 97 %
• Switchable load output
• Switchable standby function
• Extensive protective functions

Battery charger Staudte Hirsch SH-3.150, 12 V, 10 A
Item no. 331500
To the product >

---

Facial charging with the help of fully automatic 10 A battery charger

The fully automatic battery charger SH-3.150 is designed for gentle charging and optimum maintenance of 12 V lead and 12 V calcium batteries as well as 12 V lithium batteries (LiFePO₄) with integrated battery management system (BMS).

The most important features and characteristics

• Suitable for 12 V lead-acid and calcium batteries from 20 Ah upwards
• Suitable for 12 V lithium batteries with BMS from 25 Ah
• Multi-stage, microprocessor-controlled charging process
• Adjustable charging modes (AGM, acid/gel, lithium and calcium/boost)
• Regeneration mode for deeply discharged batteries
• Trickle charge and auto memory function
• Protection against short circuit, reverse polarity and overcharging
• Clear operating and display panel
• Easy operation via one button
• Jet-proof and dust-proof housing (IP 65)
• Charging adapter for PS-1200 with XLR connector

Additional benefit
The charger can also be used for charging various vehicle batteries. The charging adapters with battery clamps and ring lugs are also included.